Ultrathin RF Remote Controller
Model No.: R9
1 Zone RGB or RGBW/27 Key/Wireless Remote 30m Distance/CR2032 Battery.
Features：
● Apply to RGB or RGBW LED Controller.
● Each Remote Can Match One or More Receiver.
● CR2032 Battery Powered.
● Operate With LED Indicator Light.
Technical Parameters:
| Input and Output | |
|---|---|
| Output Signal | RF (2.4GHz) |
| Working Voltage | 3VDC (CR2032) |
| Working Current | ＜5mA |
| Standby Current | ＜2μA |
| Standby Time | 2 Year |
| Remote Distance | 30m |
| Safety and EMC | |
| EMC Standard (EMC) | EN301 489, EN 62479 |
| Safety Standard (LVD) | EN60950 |
| Radio Equipment (RED) | EN300 328 |
| Certification | CE, EMC, LVD, RED |
| Warranty | |
| Warranty | 5 Years |
| Environment | |
| Operation Temperature | Ta: -30 °C ~ +55 °C |
| Case Temperature (Max.) | Tc: +85°C |
| IP Rating | IP20 |
Key Function:
Pull Out the Plastic Battery Barrier Sheet From the Battery Compartment Located on the Bottom of the Remote
Before Key Operation.
Mode+/-: Short Press Switch Dynamic Mode Built-in Controller,
Long Press 2s Mode+ Run Mode Cycle, Long Press 2s Mode- Run the First Mode.
Speed+/-: Adjust Dynamic Mode Speed,
Short Press 10 Levels, Long Press 2s Get the Fastest / Slowest Speed.
Bright+/-: Adjust Brightness,
Short Press 10 Levels, Long Press 1-6s for Continuous 256 Levels Adjustment.
R/g/b+/-: Adjust R/G/B Brightness Respectively,
Short Press 10 Levels, Long Press 1-6s for Continuous 256 Levels Adjustment to Achieve Millions of Colors.
White: Adjust White Color,
For Rgb Light, Short Press Turn on/off White (RGB Mix),
Long Press 1-6s Adjust Saturation Continuously.
For Rgbw Light, Press W Key Will Adjust W Channel Brightness.
Short Press Turn on/off W Channel,
Long Press 1-6s Adjust W Channel Brightness Continuously.
Scene: Short Press Recall the Scene, Long Press 2s Save the Current Color Into the Scene.
Use R9 Remote Set SPI Digital LED Strip
● Set LED Strip Length [Pixel Number (8~1024)]. * + 3 Number + * For Example:
*032*, Set Pixel Number to 32.
*600*, Set Pixel Number to 600.
*1024*, Set Pixel Number to 1024.
● Set LED Strip Chip Type. * + 2 Number + *
*11*: TM1803
*12*: TM1809, TM1804, TM1812, UCS1903, UCS1909, UCS1912, UCS2903, UCS2909, UCS2912, WS2811, WS2812
*13*: TM1829
*14*: TLS3001, TLS3002
*15*: GW6205
*16*: MBI6120
*17*: TM1814B (RGBW)
*18*: SK6812 (RGBW)
*21*: LPD6803, LPD1101, D705, UCS6909, UCS6912
*22*: LPD8803, LPD8806
*23*: WS2801, WS2803
*24*: P9813
*25*: SK9822
● Set LED Strip RGB Order. * + 1 Number + *
*1*: RGB, *2*: RBG, *3*: GRB, *4*: GBR, *5*: BRG, *6*: BGR.
Match Remote Control (Two Match Ways)
End User Can Choose the Suitable Match/delete Ways. Two Options Are Offered for Selection:
Use the Controller’s Match Key
Match:
Short Press Match Key, Immediately Press on/off
Key of the Remote.
Delete:
Press and Hold Match Key for 5s to Delete All Match,
The Light Blinks 5 Times Means All Matched Remotes
Were Deleted.
Use Power Restart
Match:
Switch Off the Power, Then Switch on Power Again,
Immediately Short Press on/off Key 3 Times on the Remote.
The Light Blinks 3 Times Means Match is Successful.
Delete:
Switch Off the Power, Then Switch on Power Again,
Immediately Short Press on/off Key 5 Times on the Remote.
The Light Blinks 5 Times Means All Matched Remotes Were Deleted.
Mechanical Structures and Installations
To Fix the Remote, Two Options are Offered for Selection:
Option 1: Fix the Remote’ Back Holder on the Wall With Two Screws.
Option 2: Adhere the Remote’ Back Holder to the Wall With Paster.
Safety Information
1. Read All Instructions Carefully Before You Begin This Installation.
2. When Installing Battery, Pay Attention to the Battery Positive and Negative Polarity.
A Long Time Without Remote Control, Remove the Battery.
When Remote Distance Becomes Smaller and Insensitive, Replace the Battery.
3. If No Response From the Receiver, Please Re-match the Remote.
4. Gently Handle Remote, Beware of Falling.
5. For Indoor and Dry Location Use Only.
