SK6812 WS2812B LED Strip

What is WS2812B led strip ?

The WS2812B led strip is one kind of led strip which put IC inside the led to a smart LED control circuit and light emitting circuit in one controlled LED source, which has the shape of a 5050 LED chip. Each lighting element is a pixel, and the intensities of the pixels are contained within the intelligent digital interface input. The output is driven by patented PWM technology, which effectively guarantees high consistency of the color of the pixels. The control circuit consists of a signal shaping amplification circuit, a built-in constant current circuit, and a high precision RC oscillator. The data protocol being used is unipolar NRZ communication mode. The 24-bit data is transmitted from the controller to DIN of the first element, and if it is accepted it is extracted pixel to pixel. After an internal data latch, the remaining data is passed through the internal amplification circuit and sent out on the DO port to the remaining pixels. The pixel is reset after the end of DIN. Using automatic shaping forwarding technology makes the number of cascaded pixels without signal transmission only limited by signal transmission speed.

The LED has a low driving voltage (which allows for environmental protection and energy saving),high brightness, scattering angle, good consistency, low power, and long life. The control circuit 5050 SMD Type 0.2Watt Power integrated light source Intelligent control LED above.

SK6812 is very similar as WS2812B. They are different IC suppliers.

WS2812B led strip specification

WS2812B is one kind of addressable led strip which IC is WS2812B or we call SK6812. It’s normally RGB type, very good use for Hotel, Bar, Indoor decorate, high building ect.

Product Characteristic:

5V Addressable led strip lights
30led /60led /72led /144led per meter
PCB width is : 10MM , 12MM
Waterproof IP: IP20, IP65 and IP67

Item	Part No.	Operating Voltage	LED Type Color	LED QTY	IC QTY	Max Power	Gray Grade	Pixels	IP	Min. Cut / mm
30 LEDs / m	A2821	5V	5050 SMD RGB	30	30	9W/M	256	30	IP20	33.33
60 LEDs / m	A2818	5V	5050 SMD RGB	60	60	18W/M	256	60	IP20	16.67
72 LEDs / m	A2815	5V	5050 SMD RGB	72	72	21.6W/M	256	72	IP20	13.5
144 LEDs / m	A2812	5V	5050 SMD RGB	144	144	42W/M	256	144	IP20	6.9

Product Details:

This is Single 5050SMD with WS2812B IC inside. Put this LED on PCB to make the LED Strips.

01. ACCURATE REFLOW WELDING PROCESS
Reflow Welding Process, Low Temperature Reflow Welding, Full and Smooth Welding, Environmental Protection and Durability.

02. PURE COPPER / DOUBLE LAYER CIRCUIT
Double Layer Pure Copper Flexible Circuit Board is Adopted to Ensure Excellent Conductivity and Extremely Long Service Life of the Lamp Strip.

03. SOFT LIGHT WITH
Using the FPC as a Soft Substrate, Can Be Arbitrary Bending Will Not Break, Easy to Shape.

The typical application circuit:

Waterproof Level:

Applicable to Dry Environment

Applicable to Wet Environment

Applicable to Water Environment

Applicable to Flooded Environment

Dimensions:

5v-30LEDs/M

5v-60LEDs/M

5v-74LEDs/M

5v-144LEDs/M.

Connect Drawing:

The Installation:

(1) Paste installation:
This Installation Method is Generally Used for the Waterproof Environment,
And the High-viscosity 3m Adhesive is Attached to the Back of the Lamp Strip,
Which Can Be Directly Pasted on the Required Solid. the Surface of the Media.

Easy to Use and Easy to Install

Tear Off the Adhesive Tape

Paste to Where You Need to Install

(2) Snap-on installation:
This Installation Method is Suitable for the Casing Waterproof Product.
The Product is Fixed by the Screw Transparent Buckle to Make the Installation Firmer.