- Adopt brand LED chip,low light decay,lifespan more than 25000 hours
- Color:RGB ;
- All of materials are accord with RoHS standards
- Easy to install and preserve;can be bent freely; with 3M adhesive tape on the backside
- High color efficiency, uniform illumination
- beam angle 180°,
- IP20— non-waterproof
COB led strip specification
The COB led strip is a very good used for cover, Cabinet & Furniture soffit lighting, showcase and display path and contour making. Edge, and back lighting.
The high brightness COB led strip:
|LED Qty:||630pcs per meter||648pcs per meter||864pcs per meter|
|Input Voltage:||DC12V / DC24V||DC12V||DC12V|
|Color:||RGB 3 in 1||RGB 3 in 1||RGB 3 in 1|
|Operating temperature:||.-25 to 45℃||.-25 to 45℃||.-25 to 45℃|
|Beam angle:||180 degree||180 degree||180 degree|
|Certification:||CE; RoHS||CE; RoHS||CE; RoHS|
|Min Run:||DC12V (14.3mm)||27.78mm||41.67mm|
1. Wide viewing Angle up to 180 degree.
COB led strip are 180 degree viewing angle. SMD LED Strip type is normally 120 degree viewing angle.
Put the chips on board then put Phosphor on chips let the viewing angle bigger, then it’s less dark zone
2. 22AWG PURE COPPER WIRE
We pay attention to every details, the connect cable we use 22AWG pure copper wire. Always keep 3/8”stripped off the end of the LED for wiring purposes.
3. Waterproof type.
Non waterproof type
Extruded Silicone waterproof
Put in tube waterproof
4. Very nice color
5 . Testing report:
7. Connect drawing:
Easy to Use and Easy to Install
Tear Off the Adhesive Tape
Paste to Where You Need to Install
Free soldering Connector: 6mm; 8mm; 10mm
90 cable connector
How to cut and connect it
1. Cut the COB on the cut mark.
2. Take the 3M tape out.
3. Put the strip with the connector and connect it together.
Box Size: 43*43*35cm 100 reels per box
Weight: IP20: 12KG
5 of the Most Common Customer Questions (FAQ)
RGB COB LED strip means to make three colors of R, G and B on the same PCB board. The need for any color of the strip, or the need for gradient programs is realized through the RGB controller. There are currently two main ones: 630 and 840 lights per meter. 630 lights are 24V 10 wide PCB board, 18W per meter. The difference is that the 630 is relatively cheap, but the color of the 840 is better. The following video shows you the changing effect of RGB COB led Strip.
Yes, COB LED STRIP can be cut.
Yes, it’s can be dimmable with dimmer controller.
- The light-emitting chip adopts flip-chip technology, which has a cost advantage with the same number of lamp beads.
- Shorter heat dissipation path and lower thermal resistance, less light decay.
- No silver plating, no vulcanization risk
- Lighting angle can reach 180 degrees
- Poor color consistency control.
This is determined by the difference in the manufacturing process of COB LED STRIP and SMD light strips. The production process of SMD led strip is to first produce SMD lamp beads, and then split each lamp bead, and make the light bead after light separation to achieve color consistency on the same board. The COB LED STRIP is to flip the chip on the PCB board, and then drop the phosphor to achieve white light. Without the steps of light splitting, there is no way to achieve the consistency of the SMD led strip.
- Low power
Because the chips of the COB LED STRIP are too dense, it will affect the heat dissipation, so the power cannot be made too large, at most 14W per meter, and the SMD lamp beads of the SMD led strip have brackets, which can dissipate heat and can achieve 18W.
- Low luminous efficiency.
At present, the highest luminous efficiency of COB LED STRIP is: 120LM/W. SMD has a high-power lamp bead that can achieve 160-170LM/W. If the power requirement exceeds 120LM, you still need to choose a high-brightness SMD led strip.
- Flip chip, the defect rate is higher than that of SMD led stripwhen making waterproof led strip.