Features

  • 5 channels constant voltage output, Max. 6A current per channel, up to 720W output power.
  • Master & decoder mode, RDM function.
  • Easy operation with OLED display and 3 buttons.
  • 1/2/3/4/5 channel decoding mode selectable.
  • PWM frequency 250/500/2000/8000Hz selectable.
  • 16bit (65536 levels) /8bit (256 levels) grey level selectable.
  • Output dimming curve gamma value 0.1-9.9 selectable.
  • Stand-alone RGB mode and 5 channel dimmer mode selectable,

work as DMX master(8 bit) to control other decoders.

  • Built-in 25 RGB programs, speed and brightness adjustable.
  • Support 3 kinds of DMX ports: Green terminal(amplify output), XLR3 and RJ45 port.
  • Comply with the DMX512 standard protocols.
  • Over-heat / Over-load / Short circuit protection, recover automatically.
  • With fast self-testing function.

Technical Parameters

Input and Output
Input voltage 12-24VDC
Input current 30.5A
Output voltage 5 x (12-24)VDC
Output current 5CH,6A/CH
Output power 5 x (72-144)W
Output type Constant voltage
Environment
Operation temperature Ta: -30 OC ~ +55 OC
Case temperature (Max.) T c: +85OC
IP rating IP20
Safety and EMC
EMC standard (EMC)

EN55032:2015,

EN61000-3-2:2014,

EN61000-3-2:2013,

EN55024 :2010/A1:2015
Safety standard(LVD) EN 61347-1:2015

EN 61347-2-11:2015
Certification CE,EMC,LVD
Warranty and Protection
Warranty 5 years
Protection Reverse Polarity                               Over-heat                                           Over-load                                             Short circuit

OLED screen interface

Short press M key, switch between DMX decoder mode, Dimmer mode and RGB controller mode.

Long press M key or short press < or > key, enter parameter setting state.

When in parameter setting state, short press M key to switch between multiple parameter item,

press < or > key for parameter adjustment.

long press M key or wait 30s to quit parameter setting state.

Long press M & > key for 2s, enter fast self-testing.

Long press < & > key for 2s, restore factory default parameter.

DMX decoder mode

DMX decode start address:

Range: 001~999

DMX decode mode:

1CH (DIM) 2CH (CCT) 3CH (RGB) 4CH (RGBW) 5CH (RGB+CCT)

Output PWM frequency:

Std (2KHz)

High (8KHz)

Mid (500Hz)

Low (250Hz)

Higher PWM frequency, will cause lower output current,

higher power noise, but more suitable for camera(No flflickers for video).

Grey level:

8bit

16bit (choose it if the DMX master support 16 bit)

Output dimming curve(Only valid for 8bit Grey level):

Standard (Gamma 1.6)

Linear

Gamma0.1-9.9

It is recommended to use standard,

0.1-9.9 is for special requirements.

DMX master mode as 5 channel dimmer

Each or all channel brightness setting:

Range: 0-255

Dynamic RGB mode:25 kinds

Mode speed:Range: 1-10 level

Mode brightness:Range: 10%-100%

Ch4 brightness:Range: 0-255

Ch5 brightness:Range: 0-255

Dynamic RGB mode list:

No. Name No. Name No. Name
01 Static Red+strobe 09 R/G/B gradual 17 Green/White gradual
02 Static Green+strobe 10 Color gradual 18 Blue/White gradual
03 Static Blue+strobe 11 R/G/B fade 19 Red/Yellow gradual
04 Static White+strobe 12 Red fade 20 Red/Purple gradual
05 R/G/B jump 13 Green fade 21 Green/Yellow gradual
06 7 Color jump 14 Blue fade 22 Green/Cyan gradual
07 R/G/B strobe 15 White fade 23 Blue/Purple gradual
08 7 Color strobe 16 Red/White gradual 24 Blue/Cyan gradual
25 All loop play

Address setting table

Wiring Diagram

Note:

  1. Connecting with green terminal(DMX AMP) or an extra amplifier will be needed when more than 32 decoders

are connected, or use overlong signal line, signal amplification should not be more than 5 times continuously.

  1. If the recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W

90-120Ω terminal resistor at the end of each DMX signal line.

Address setting table

8bit:

Decode Mode 1CH DIM 2CH CCT 3CH RGB 4CH RGBW 5CH RGB+CCT
Address Quantity 1 2 3 4 5
Channel 1 001 001 001 001 001
2 001 002 002 002 002
3 001 001 003 003 003
4 001 002 003 004 004
5 001 002 003 004 005

16bit:

Decode Mode 1CH DIM 2CH CCT 3CH RGB 4CH RGBW 5CH RGB+CCT
Address Quantity 2 4 6 8 10
Channel 1 001

002

 001

002

 001

002

 001

002

 001

002
2 001

002

 003

004

 003

004

 003

004

 003

004
3 001

002

 001

002

 005

006

 005

006

 005

006
4 001

002

 003

004

 005

006

 007

008

 007

008
5 001

002

 003

004

 005

006

 007

008

 009

010

Note: even channel for micro dimming.

Malfunctions analysis & troubleshooting

Malfunctions Causes Troubleshooting
No light 1. No power.

2. Wrong connection or insecure.

 1. Check the power.

2. Check the connection.
Wrong color 1. Wrong connection of R/G/B/W wires.

2. DMX decode address error.

 1. Reconnect R/G/B/W wires.

2. Set corrrect decode address.
Uneven intensity between front and rear,with voltage drop 1. Output cable is too long.

2. Wire diameter is too small.

3. Overload beyond power supply capability.

4. Overload beyond controller capability.

 1. Reduce cable or loop supply.

2. Change wider wire.

3. Replace higher power supply.

4. Add power repeater.