Features Details Video Installation Accessories FAQ

Product Features:

This Board-to-Board Connector is Used to Splice Two Segment of WATERPROOF 5050 RGB LED Strip Light That is 10mm Wide (EXCEPT Silicon Coating). If Your Waterproof Material is Silicon, Please Buy Our NON-WATERPROOF Version by Searching B074LVGD1M. It Still Work Without Peeling Silicon
Using Pierce-to-Contact Technology, the Pin Go Through Strip Light’s FPC to Make Connection Possible, in This Way It Bites FPCB Unbelievably Firmly Without Worry It Slip Out of Connector. Perfectly Work With Tape Light With 3M VHB Red Foam Back Adhesive Tape Which is Too Thick to Put Into Conventional Led Snap Connector
Also Applicable to Waterproof Pixel Dream Color Led Strip Coming With 4 Soldering Pad,for Example WS2813
Up to 5A Current ( R,G,B 3 Channel ) Supported, Allow You to Connect Longer LEDStrip by One Connector
Clear Cap Will Not Cover the Light From First SMD of Each Strip Light Segment, Allowing Light to Go Through It, You Can Hardly See Dark Area Casting to Lighting Target, Enjoy Really Continuous Linear Illumination Effect.

Product Specifications:

2P-5mm Board to Board (Bare Board) / Board to Board (Eppel), /Board to Line (Bare Board) / Board to Line (Eppel)
2P-8mm Board to Board (Bare Board) / Board to Board (Eppel), /Board to Line (Bare Board) / Board to Line (Eppel)
2P-10mm Board to Board (Bare Board) / Board to Board (Eppel), /Board to Line (Bare Board) / Board to Line (Eppel)
3P-10mm Board to Board (Bare Board) / Board to Board (Eppel), /Board to Line (Bare Board) / Board to Line (Eppel)
4P-10mm Board to Board (Bare Board) / Board to Board (Eppel), /Board to Line (Bare Board) / Board to Line (Eppel)
5P-12mm Board to Board (Bare Board) / Board to Board (Eppel), /Board to Line (Bare Board) / Board to Line (Eppel)
6P-12mm Board to Board (Bare Board) / Board to Board (Eppel), /Board to Line (Bare Board) / Board to Line (Eppel)

Product Details:

Wateproof connectors

2pin wateproof connectors

3pin wateproof connectors

4pin wateproof connectors

Non wateproof connectors

3pin Non wateproof connectors

4pin Non wateproof connectors

5pin Non wateproof connectors

6pin Non wateproof connectors

01. WATEPROOF CONNECTORS
Open the Transparent Cover up to 90 Degrees.

02. ALIGNMENT WIRING
Close the Transparent Cap With Pliers or Other Tools Until It is Fully
Seated on Both Sides of the Base.

03. CONNECT PROPERLY
Insert the Strip to the End of Connector  Keep the Silicone Face
up , ( No Need to Remove Silicone Glue)

04. END INSTALLATION
Insert Wires Into Guide Slot Directly, No Stipping.

Multiple Ways of Linking:

01. Making Strip to Strip Bridge Wire.

02. Making Strip to Power Connector Wire.

 

 

SAFETY INFORMATION
· Please Consult an Electrician Before Doing Any Electrical Worker.
· The Strip and Its Components Cannot Be Mechanically Pressed.
· Correct Electrical Polarity Needs to Be Addressed.
· Pay Attention to ESD Precautions During Assembly.
· Installation Should Be Done by an Electrician.

STORAGE CONDITIONS
· The LEDs Should Be Kept at ≤86°f and ≤70%RH.
· When Storing the LEDs Use Moisture Proof Packaging.

The Installation:

(1) Paste Installation:
This Installation Method is Generally Used for the Waterproof Environment,
And the High-Viscosity 3M Adhesive is Attached to the Back of the Lamp Strip,
Which Can Be Directly Pasted on the Required Solid. The Surface of the Media.

Easy to Use and Easy to Install

Tear Off the Adhesive Tape

Paste to Where You Need to Install

(2) Snap-on Installation:
This Installation Method is Suitable for the Casing Waterproof Product.
The Product is Fixed by the Screw Transparent Buckle to Make the Installation Firmer.

Accessories (Clips+Screw+Screwd-Diver)

Put the Clips on the Strip

Fixed the Clips

Accessories Display:

Hippo Buckle

Controller

Aluminum Trough

Power Supply

Applications:

  • Architectural Lighting for Canopies, Corridors, Archways, Windows.
  • Downlighting or Uplighting for Wall Wash Applications.
  • Backlighting or Edge Lighting for Signage.
  • Edge-Lighting for Glass.
  • Under-cabinet, Toe-Kick, In-Cove Moldings.
  • DIY Projects
  • Safety Stair Tread and Step Marking.
  • Decorative Lighting for Holidays, Tradeshows, Exhibitions.

Note: Luminous flux information applies only to white LEDs. Color LEDs are measured in mcd, rather than lm. Contact a sales representative for assistance.