

Features
- 12 channels constant voltage output, Max. 5A current per channel, up to 1440W output power.
- Master & decoder mode, RDM function.
- Easy operation with OLED display and 4 buttons.
- DIM/CCT/RGB decoding mode selectable.
- PWM frequency 250/500/2000/8000Hz selectable.
- 16bit (65536 levels) /8bit (256 levels) grey level selectable.
- Output dimming curve gamma value 0.1-9.9 selectable.
- Stand-alone RGB mode and 12 channel dimmer mode selectable,
work as DMX master(8 bit) to control other decoders.
- Built-in 10 RGB programs, speed and brightness adjustable.
- Comply with the DMX512 standard protocols.
- DMX signal optoelectronic isolation / amplify.
- Over-heat / Over-load / Short circuit protection, recover automatically.
- With fast self-testing function.
Technical Parameters
INPUT AND OUTPUT | |
---|---|
Input Voltage | 12-24VDC |
Input current | 60.5A |
Output voltage | 12 x (12-24)VDC |
Output current | 12CH,5A/CH |
Output power | 12 x (60-120)W |
Output type | Constant voltage |
SAFETY AND EMC | |
EMC Standard (EMC) | EN55032: 2015, EN61000-3-2: 2014, EN61000-3-2: 2013, EN55024 : 2010/A1: 2015 |
Safety Standard(LVD) | EN 61347-1: 2015 EN 61347-2-11: 2015 |
Certification | CE, EMC, LVD |
WARRANTY AND PROTECTION | |
Warranty | 5 years |
Protection | Reverse Polarity
Over-heat Over-load Short circuit |
ENVIRONMENT | |
Operation Temperature | Ta: -30 °C ~ +55 °C |
Case Temperature (Max.) | Tc: +85°C |
IP Rating | IP20 |
OLED screen interface

Short press MODE key, switch between DMX decoder mode, Dimmer mode and RGB controller mode.
Short press SETUP key, enter parameter setting state, and switch between multiple parameter item.
press < or > key for parameter adjustment.
long press SETUP key or wait 30s to quit parameter setting state.
Long press M & > key for 2s, enter fast self-testing.
Long press < & > key for 2s, restore factory default parameter.
DMX decoder mode

DMX decode start address:
Range: 001~999
DMX decode mode:
DIM (1CH single color) CCT (2CH color temperature) RGB (3CH)
Output PWM frequency:
Std (2KHz)
High (8KHz)
Mid (500Hz)
Low (250Hz)
Higher PWM frequency, will cause lower output current,
higher power noise, but more suitable for camera(No flflickers for video).
Grey level:
8bit
16bit (choose it if the DMX master support 16 bit)
Output dimming curve(Only valid for 8bit Grey level):
Standard (Gamma 1.6)
Linear
Gamma0.1-9.9
It is recommended to use standard,
0.1-9.9 is for special requirements.

DMX master mode as 12 channel dimmer

Each channel brightness setting:
Range: 0-255
<<&>>:
press < or > key to switch between previous or next page, each page 3 channel.
DMX master mode as RGB controller

Dynamic RGB mode:10 kinds
Mode speed:Range: 1-10 level
Mode brightness:Range: 10%-100%
Dynamic RGB mode list:
No. | Name |
01 | White chase jump |
02 | White synchronous fade |
03 | White chase fade |
04 | R/G/B/W synchronous jump |
05 | R/G/B/W chase jump |
06 | Color synchronous gradual |
07 | Color jump gradual |
08 | R/G/B/W synchronous fade |
09 | R/G/B/W chase fade |
10 | All mode loop play |